logo
 
left right
shadow
CREEP TEST APPARATUS
TECHNICAL DETAIL 
ASTM- C512 , designed to determine the Creep of Mould Concrete cylinder subjected to sustained longitudinal Compressive load.
Creep Rig Tester Including Moulds for Concrete Conforming to ASTM C512.Test Rig Essentially Comprising of Main Sub-Assembly Reaction Frame Made of Mild Steel With Tie Rods Plated With Black Zinc( 1 No. ) Electrically Operated Hydraulic Pump With Gauge( 1 No. ) Hydraulic Jack With 4 MTR. Hose & Quick Release Coupling 1 No & Reaction Frame. Test method be limited to Concrete with maximum aggregate size of 2 inch (50mm). Suitable for supply on 220V, 50Hz, Single phase AC only.
The Instrument would consists of following parts:-
Electrically Operated Hydraulic Pump With Pressure Gauge Fitted With Pump, Reaction frame suitable for 3No. 150 mm dia X 300mm long cylinder sample, load gauge.
Reaction frame :- consisting of Upper and Lower jack plates and upper & lower loading plates bearing on the ends of the loaded specimen, load maintaining elements(springs), threaded rods and nuts to take the reaction of loaded system.
Pumping Unit:- Motorized pump unit of 1000KN housed in an elegant cabinet and of two speed design driven by an electric motor . The Motor be supplied with ON /OFF switch push button, slow fast lever supplied with a knob.
Hydraulic Jack:- consisting of cylinder and piston , lifting the handle would be provided with cylindrical body, with inlet nozzle fixed for coupling with  the connecting pipe with Teflon seal provided on the hydraulic jack to prevent leakage of the oil under pressure.
Load Gauge :- The load indicated on 20cm dial load gauge 1000KN capacity.

CONCRETE PERMEABILITY APPARATUS
TECHNICAL DETAIL
1048, Consisting of
1.Three Specimen Holder Assemblies as per DIN-1048 With A Manifold Assembly
2.Panel Fitted With Pressure Regulator, Pressure Gauge (4 No) With Pressure Lines- 1 No.
3.Hose Pipe- 3 No.
4.Spanner- 3 No.
5.Tommy Pin- 2 No.
6.Permeability Cell Top/ Bottom Pleats Assembly (Sample Holding Device)- 3 No.
7.Stand Side Frame for Panel Mounting- 1 No.
8.Stand Side Frame for Panel Mounting- 1No.
9.Stand for Mounting Three Sample Holding Device- 1 No.
10Connecting Flat Patti- 2 No.
11Air Compressor working Pressure 15 Kg. cm2, 2 HP Pressure Capacity 15 kg/cm2 Air Pressure Capacity 100 Liters - 1 no.
12Connecting Pipe- 1 No.
13Filter- 2 No.
14Pressure Gauge- 1 No.
15Operating Manual & Packing List With Certificate – 1 No.

DIGITAL MORTAR MIXER
TECHNICAL DETAIL 
Automatic Mortar Mixer, 5 litres nominal capacity
for Preparation of standard prisms with Automatic/Manual mixing procedure in accordance with IS: 10890, EN 196-1 & EN 196-3, designed to prepare cement mortar for strength determination as specified in IS:4031.
Features :
•Microprocessor control
•Choice of automatic mixing cycles as per EN Std.
•User defined mixing cycle
•Sand Dispenser
•Water burette
The mixer would is designed to mix mortars and cement pastes primarily to  the requirements of EN 196. The mixing paddle would have a planetary motion and be driven by a motor with a microprocessor based speed and program controller. The mixer would be operated either in an automatic or manual mode. When the mixer is used in the manual mode, the two mixing speeds can be changed by means of a soft touch button, without switching off the motor. In the automatic mode any one of the pre-set mixing programmes may be selected.
Standard Supply includes:
Basic unit with stainless steel mixing bowl and stirrer, Program controller with status indicators to run the
Mixer in fully Automatic or Manual mixing mode.
Technical Specifications :
Low Speed 140 +/- 5 High Speed 285+/-10
Suitable for operation on 220V, 50Hz, single phase, AC supply.

VIBRATION MACHINE FOR MORTAR
TECHNICAL DETAIL
Ref. Standard - IS:4031 , IS:10080, EN 196-1 413-2, EN 13454-2
A specially designed Vibration Machine used for vibrating the mix in moulds at a frequency of 12,000 ± 400 cycles per minute, The Vibrator would be mounted over coiled springs and the vibrations be developed by means of a revolving eccentric shaft. 
Design of the machine facilitate easy assembly and dismantling of the cube moulds. 
Machine one cube mould with ISI Certification Mark and poking rod.
The machine with NCCBM certificate for its frequency. 
Suitable for operation on 220V, 50Hz, Single Phase, AC supply.
The equipment consist of the following replaceable parts :
•Mould Steel, for 70.6 mm Cube with ISI Certification Mark as per IS:10080,
•Side Spring,
•Supporting Springs (Set of four),
•Springs, for Fitting Mould (Set of two),
•Endless Belt,
•Belt Guard,
•Eccentric Shafts with bearing.
 

BIOLOGICAL SAFETY CABINET
 
TECHNICAL DETAIL
Interior construction would be made of stainless steel.
 
 
 
Exterior construction would be made of steel with heat cured epoxy coating.
Would have HEPAfilter (with 99.97% efficient at 0.3μm particles) as a Main
 
 
filter which produces class 100 or better clean air environment.
 
Would have HEPA filter (with 99.97% efficient at 0.3μm particles) as an exhaust filter
Blower would be on top for best results & easy servicing.
Would have specialized sound absorbing materials which reduces sound Significantly.
Would have low discharge volume & and quite operation mechanism.
Main Filter would be removable from front for easy servicing & replacement.
Would have high efficiency UV light which comes with stronggermicidal power
 
& disinfects environment in 30 minutes.
 
 
 
Would have counter balanced sliding sash (acrylic) door to ensure clear view of work area.
 
 
 
Would provide with castor wheels for ease of mobility.
 
 
 
Would have independent ON / OFF switch for blower, fluorescent lamp & UV
 
 
 
lamp with visual status indication.
 
 
 
Would have unique openable base stand with castors.
 
 
 
Would have LCD microprocessor based controller with Auto & Manual mode.
 
 
 
Would have digital differential pressure indication for Inflow & Down flow.
 
 
 
Would have safety audio & visual alarm for HEPA blockage, UV on & sash door level.
 
 
 
Would have feature of auto UV light off when sash door opens. Would have UV counter.
 
 
Would have provision for gas, air & electric socket.

Prev 1  2  3  4  5  6  7  8   Next
BIOLOGICAL SAFETY CABINET    VIBRATION MACHINE FOR MORTAR    DIGITAL MORTAR MIXER    CONCRETE PERMEABILITY APPARATUS    CREEP TEST APPARATUS    
Categories
 CHEMICAL REACTION ENGINEERING LAB
 CIVIL LAB EQUIPMENTS
 CORE LAB
 ELECTRICAL ENGINEERNG LAB EQUIPMENTS
 ELECTRONICS ENGINEERING LAB EQUIPMENTS
 FLUID MACHINERY LAB
 FLUID MECHANICS LAB
 HEAT TRANSFER LAB
 HYDRAULIC BENCH & ACCESSORIES
 MASS TRANSFER LAB
 MATERIAL TESTING LAB
 MECHANICAL OPERATION LAB
 METALLURGICAL & MATERIAL SCIENCE LAB
 MOMENTUM TRANSFER LAB
 MONENTUM TRANSFER LAB
 PETROLEUM TESTING LAB
 PHYSICS LAB
 PROCESS CONTROL & INSTRUMENTATION LAB
 PRODUCTION LAB
 REFRIGERATION & AIR CONDITIONING LAB
 STRENGHT OF MATERIAL LAB
 STRUCTURE LAB
 THEORY OF MACHINE LAB
 THERMODYNAMICS LAB
 WORKSHOP
 
Follow us on
facebook twitter in  
 
bottom
 
Home About us Products Enquiry Contact us