logo
 
left right
shadow
VENTURIMETER & ORIFICEMETER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-10
DESCRIPTION:
The apparatus consists of two pipelines emerging out from a common manifold.  One pipe line contain a Venturimeter and other contains an Orifice. The pressure tapings from the Venturimeter and orifice meter are taken to differential manometer to measure pressure difference. The Venturimeter and Orifice meter are connected in parallel and any one of them can be put in operation by operating valves provided at the downstream. The flow can also be regulated by these valves.  Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.
EXPERIMENTATION:
To demonstrate the use of Venturimeter & Orifice meter as flow meters.
To determine co-efficient of discharge through Venturimeter and Orifice meter.
Electricity Supply: Single Phase, 220V AC, 50 Hz, 5-15 amp combined socket with earth connection.
UTILITIES REQUIRED
Water Supply (Initial Fill).
Floor Drain Required.
Floor Area Required: 1.5 x 0.75 m.
Mercury (Hg) for manometer (250 gm).
TECHNICAL DETAILS :
Venturimeter  Material Clear Acrylic compatible to 1” Dia. Pipe.
Orifice meter  Orifice plate made of Stainless Steel and housing made of Clear Acrylic compatible to 1” Dia. Pipe.
Water Circulation   : FHP Pump, Crompton make.
Flow Measurement Using Measuring Tank with Piezometer (Capacity 25 Ltrs.) and Electronic Stop Watch
Sump Tank  Capacity 50 Ltrs.
Control Panel Comprises of:
Standard make On/Off Switch, Mains Indicator, etc.
Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus.
Tanks will be made of Stainless Steel.
The whole set-up is well designed and arranged in a good quality painted structure.
 
 

VENTURIMETER, ORIFICEMETER & ROTAMETER TEST RIGMAKE : CREATIVE LAB MODEL NO:-CLFM-11
DESCRIPTION :
The apparatus consists of three pipelines emerging out from a common manifold.  One pipe line contain a Venturimeter, second contains an Orifice and third pipe line contains a Rota meter. The pressure tapings from the Venturimeter and Orifice meter are taken to differential manometer to measure pressure difference. The Venturimeter, Orifice meter and Rota meter are connected in parallel and any one of them can be put in operation by operating valves provided at the downstream. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank & stop watch.
EXPERIMENTATION:
To determine the co-efficient of discharged through Venturimeter and orifice meter. 
To measure discharge through Venturimeter, Orifice meter and Rota meter
To calibrate the Rotameter.
UTILITIES REQUIRED:
Electricity supply: Single Phase, 220 V AC, 50 Hz, 5-15 amp combined socket with earth connection.
Water Supply (Initial Fill).
Floor Drain required.
Floor Area Required:  1.5 m x 0.75 m.
TECHNICAL DETAILS
Venturimeter : Material Clear Acrylic compatible to 1”Dia. Pipe.
Orificemeter : Orifice plate made of Stainless Steel and housing made of Clear
Acrylic compatible to 1” Dia. Pipe.
Rotameter : Compatible Range. Eureka make.
Water Circulation : FHP Pump, Crompton make.
Flow Measurement : Using Measuring Tank (Capacity 25 ltrs.) and Electronic Stop
Watch.
Sump Tank: Capacity 50 Ltrs.
Control Panel Comprises of :Standard make On/Off Switch, Mains Indicator, etc.
Instruction Manual : An ENGLISH instruction manual will be provided along
With the Apparatus
Tanks will be made of Stainless Steel.
The whole set-up is well designed and arranged in a good quality painted structure.
 
 

NOZZLE METER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-12
 
DESCRIPTION:
The apparatus consists of a Nozzle meter made of stainless-steel houses in Acrylic Test Section. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.
EXPERIMENTATION:
To measure discharge through Nozzle meter.
To calculate co-efficient of discharge for nozzle meter.
UTILITIES REQUIRED :
Electricity Supply: Single Phase 220 V AC, 50Hz, 5-15 amp combined socket with earth connection.
Water Supply (Initial Fill).
Floor Drain required.
Mercury (Hg) for manometer(250 gm)
Floor Area Required:    1.5 m x 0.75 m
TECHNICAL DETAILS :
Nozzle meter : Nozzle of Stainless Steel, Housing of Clear Acrylic.
Compatible to 1” dia pipe.
Water Circulation : FHP Pump, Crompton make
Flow Measurement : Using Measuring Tank, (Capacity 25 Ltrs. (approx.))
and Electronic Stop Watch
Sump Tank : Capacity 55 Ltrs. (approx.)
Control Panel Comprises of :
Standard make On/Off Switches, Mains Indicator, etc.
Instruction Manual : An ENGLISH instruction manual will be provided along
with the Apparatus Tanks will be made of Stainless Steel.
The whole set-up is well designed and arranged in a good quality painted structure
 
 

PITOT TUBE SETUP MAKE : CREATIVE LAB MODEL NO:-CLFM-14
DESCRIPTION:
A Pitot tube is used to measure the local velocity at a given point in the flow stress. A pitot tube of standard design made of copper/SS is supplied and is fixed below vernier scale. The vernier scale is capable to measure the position of Pitot tube in transparent section.  The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.
EXPERIMENTATION:
To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube.
To plot velocity profile across the cross section of pipe.
UTILITIES REQUIRED:
Electricity Supply: Single Phase, 220V AC, 50Hz, 5-15 amp combined socket with earth connection.
Water Supply (Initial Fill).
Floor Drain required.
Floor Area Required: 1.5 x 0.75 m.
Chemical Required: CCl4 - 50 ml and Iodine pallets for CCl4.
TECHNICAL DETAILS:
Pitot tube  Material Copper/SS of compatible size fitted with vernies  scale.
Test Section  Material Clear Acrylic, compatible to 1” Dia. Pipe.
Water Circulation FHP Pump, Crompton make.
Flow Measurement  Using Measuring Tank with Piezometer (Capacity 25 Ltrs.)
Electronic Stop Watch
Sump Tank   Capacity 50 Ltrs.
Control Panel Comprises of       :
Standard make On/Off Switch, Mains Indicator, etc.
Instruction Manual   An ENGLISH instruction manual will be provided along  With the Apparatus Tanks will be made of Stainless Steel.
 
 

CAVITATION APPARATUS MAKE : CREATIVE LAB MODEL NO: CLFM-15
DESCRIPTION :
The apparatus has been designed to demonstrate the phenomena of Cavitation. The present set-up consists of a test section made of Acrylic  having conversion and diversion section. Pressure tapings at appropriate position are provided. This test section  is having one control valve at upstream side to regulate the water flow rate. Two pressure gauges are connected to these taping which give the pressure readout at the time of flow passing through this test section. The unit is self-contained close circuit type with sump tank, measuring tank and centrifugal pump. Flow through test section can be regulated with the help provided by-pass and control valve.
EXPERIMENTATION:
To observe the phenomena of cavitation.
To compare the theoretical and actual pressures at cavitation condition.
UTILITIES REQUIRED :
Water Supply : Initial Fill.
Floor Drain Required.
Floor Area Required : 1.5 m x 1 m.
TECHNICAL DETAILS :
Test Section : Material Acrylic
Pressure Gauge : 0-4 kg/cm2
Vacuum Gauge  : 0-760 mmHg
Water Circulation : By Pump Crompton make.
Flow Measurement : Measuring Tank (Capacity : 40 liters) & Electronic Stop Watch
Sump Tank : Capacity : 60 liters
Control Panel Comprises of :
Standard make On/Off Switch, Mains Indicator, etc.
Instruction Manual : An ENGLISH instruction manual will be provided along
with the Apparatus Tanks will be made of Stainless Steel.
The whole set-up is well designed and arranged in a good quality painted structure
 
 

Prev   1  2  3  4  5  6  7  8   Next
CAVITATION APPARATUS MAKE : CREATIVE LAB MODEL NO: CLFM-15    PITOT TUBE SETUP MAKE : CREATIVE LAB MODEL NO:-CLFM-14    NOZZLE METER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-12    VENTURIMETER, ORIFICEMETER & ROTAMETER TEST RIGMAKE : CREATIVE LAB MODEL NO:-CLFM-11    VENTURIMETER & ORIFICEMETER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-10    
Categories
 CHEMICAL REACTION ENGINEERING LAB
 CORE LAB
 FLUID MACHINERY LAB
 FLUID MECHANICS LAB
 HEAT TRANSFER LAB
 HYDRAULIC BENCH & ACCESSORIES
 MASS TRANSFER LAB
 MECHANICAL OPERATION LAB
 METALLURGICAL & MATERIAL SCIENCE LAB
 MOMENTUM TRANSFER LAB
 MONENTUM TRANSFER LAB
 PETROLEUM TESTING LAB
 PROCESS CONTROL & INSTRUMENTATION LAB
 PRODUCTION LAB
 REFRIGERATION & AIR CONDITIONING LAB
 STRENGHT OF MATERIAL LAB
 STRUCTURE LAB
 THEORY OF MACHINE LAB
 THERMODYNAMICS LAB
 
Follow us on
facebook twitter in  
 
bottom
 
Home About us Products Enquiry Contact us