TEN TUBE MANOMETERS FLOW CHANNEL ACCESSORIES, EXPERIMENTAL FLUME FLOW CHANNEL MAKE: CREATIVE LAB MODEL NO: CLFM-52, SEDIMENT FEEDER FLOW CHANNEL ACCESSORIES, manufacturers suppliers in India

SEDIMENT FEEDER FLOW CHANNEL ACCESSORIES

DESCRIPTION
Sediment feed using a vibrating conveyor, use together with the sediment trap

FEATURES

Sediment feed using a vibrating conveyor

LEARNING OBJECTIVES/EXPERIMENTS

Observation of bed-load transport along the flume bottom

Rolling and saltation bed-load transport

Influence of flow velocity on bed load transport

Fluvial obstacle marks

SPECIFICATION

Sediment feeder for a sediment feed to the experimental flume

Accessory for the sediment trap

Mounting above the inlet of the experimental section of experimental flume

TECHNICAL DATA

FEEDER

Feed rate: 0.1m3/h

Frequency: 3600min-1

Funnel content: 10L

230V, 50Hz, 1 phase

230V, 60Hz, 1 phase

120V, 60Hz, 1 phase

UL/CSA optional

LxWxH: 450x220x460mm (feeder); Weight: approx. 20kg

EXPERIMENTAL FLUME FLOW CHANNEL MAKE: CREATIVE LAB MODEL NO: CLFM-52

DESCRIPTION

Experimental section lengths of 2.5 m extendable up to 5 m closed water circuit and inclination adjustment

This is a self-contained open channel designed for studying flow phenomena with a change in bed slope. It is to be used with optional accessories and models below.

The channel is of rectangular cross section supported by a rectangular steel frame. Side walls are transparent to allow full visual observation and are supported by adjustable steel brackets to ensure accurate wall alignment. Tilting can be adjusted by a manual screw jack. The middle section of the bed can be adjusted manually upward or downward by a screw. A head tank with a stilling baffle provides smooth flow and water is returned to the storage tank via an end tank. Models are attached to the top edges or bed of the flume by screws. Screw holes at the bed can also be used for pressure tapping to measure pressure loss along the channel length.

FEATURES

Basic principles of open-channel flow

Experimental section with transparent side walls, lengths of 2.5m. (total length along with extension element will be 5 meter)

Homogeneous flow through carefully designed inlet element

Models from all fields of hydraulic engineering available as accessories

LEARNING OBJECTIVES/EXPERIMENTS

Together with optionally available models

Uniform and non-uniform discharge

Flow formulae

Flow transition (hydraulic jump)

Energy dissipation (hydraulic jump, stilling basin)

Flow over control structures: weirs sharp-crested broad-crested, ogee-crested discharge under gates

Flow-measuring flumes

Local losses due to obstacles

Transient flow: waves

Vibrating piles

Sediment transport

SPECIFICATION

Illustrates basic principles of open-channel flow.

The experimental flume with experimental section, inlet and outlet element and closed water circuit, length of each experimental section 2.5 meter and 5 meters with extension element.

Smoothly adjustable inclination of the experimental section.

Experimental section with 10 evenly spaced threaded holes on the bottom for installing models or for water level measurement using pressure.

Side walls of the experimental section will be made of tempered glass for excellent observation of the experiments.

All surfaces in contact with water will be made of corrosion-resistant materials

Flow-optimized inlet element for low-turbulence entry into the experimental section

Closed water circuit with water tank, pump, rotameter and manual flow adjustment

Models from all fields of hydraulic engineering will be available as accessories

TECHNICAL DATA

Experimental section: length: 2.5m; flow cross-section W x H: 86x300 mm; inclination adjustment: -0,5...+3%

Tank: 280L

GLASS REQUIREMENT OF EXPERIMENTAL SECTION:

Single pane safety glass conforming to European Standard EN 12150-1, thickness 8 mm

PUMP SPECIFICATIONS

Power consumption: 1.0kW

High Pressure Centrifugal Pump, series EVMS

Type: EVMS 10-2 N5 HQGQ1EGE/0.75M1 ~ 230V/50Hz

H/max: 21.0 m

Q/max: 15 m3/h

Outer casing: 1.4301

Lower casing: 1.4301

Impeller: 1.4301

Shaft: 1.4301

EXTENSION ELEMENT OF THE EXPERIMENTAL FLUME

Modular element for extending the working section

FEATURES

Element to extend the experimental section to 5m

Simple assembly by the user

SPECIFICATION

Element to extend the experimental section to 5m

Element with 10 evenly spaced threaded holes on the bottom for installing models or for water level measurement using pressure

Side walls made of tempered glass for excellent observation of the experiments

TECHNICAL DATA

Flow cross-section: WxH: 86x300 mm; length: 2.5 m; LxWxH: 2500x186x395 mm

TEN TUBE MANOMETERS FLOW CHANNEL ACCESSORIES

DESCRIPTION
Simultaneous display on tube manometers of up to ten discharge depths along the experimental section

FEATURES

Simultaneous display of ten discharge depths along the experimental section

SPECIFICATION

Simultaneous display on tube manometers of up to ten discharge depths along the experimental section of experimental flume

Manometer holding device mounted directly at the experimental section of experimental flume

Holding device fitted with screws and spirit level to compensate for the inclination of the experimental section

Set of hoses to connect measuring points of the experimental section and tube manometers

Technical data

Measuring ranges

0... 300mmWC, graduation: 1 mm

LxWxH: 240x90x430 mm

Weight: approx. 3kg (without hoses)

INSTRUCTION MANUAL

Instruction manual will be provided along with the apparatus.

Prev 1 2 3 4 5 6 Next

TEN TUBE MANOMETERS FLOW CHANNEL ACCESSORIES EXPERIMENTAL FLUME FLOW CHANNEL MAKE: CREATIVE LAB MODEL NO: CLFM-52 SEDIMENT FEEDER FLOW CHANNEL ACCESSORIES