METACENTRIC HEIGHT APPARATUS MAKE : CREATIVE LAB MODEL NO:-CLFM-17, LAMINAR FLOW TABLE MAKE :CREATIVE LAB MODEL NO:-CLFM-16, CAVITATION APPARATUS MAKE : CREATIVE LAB MODEL NO: CLFM-15, PITOT TUBE SETUP MAKE : CREATIVE LAB MODEL NO:-CLFM-14, NOZZLE METER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-12, manufacturers suppliers in India

NOZZLE METER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-12

DESCRIPTION:

The apparatus consists of a Nozzle meter made of stainless-steel houses in Acrylic Test Section. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

EXPERIMENTATION:

To measure discharge through Nozzle meter.

To calculate co-efficient of discharge for nozzle meter.

UTILITIES REQUIRED :

Electricity Supply: Single Phase 220 V AC, 50Hz, 5-15 amp combined socket with earth connection.

Water Supply (Initial Fill).

Floor Drain required.

Mercury (Hg) for manometer(250 gm)

Floor Area Required: 1.5 m x 0.75 m

TECHNICAL DETAILS :

Nozzle meter : Nozzle of Stainless Steel, Housing of Clear Acrylic.

Compatible to 1” dia pipe.

Water Circulation : FHP Pump, Crompton make

Flow Measurement : Using Measuring Tank, (Capacity 25 Ltrs. (approx.))

and Electronic Stop Watch

Sump Tank : Capacity 55 Ltrs. (approx.)

Control Panel Comprises of :

Standard make On/Off Switches, Mains Indicator, etc.

Instruction Manual : An ENGLISH instruction manual will be provided along

with the Apparatus Tanks will be made of Stainless Steel.

The whole set-up is well designed and arranged in a good quality painted structure

PITOT TUBE SETUP MAKE : CREATIVE LAB MODEL NO:-CLFM-14

DESCRIPTION:

A Pitot tube is used to measure the local velocity at a given point in the flow stress. A pitot tube of standard design made of copper/SS is supplied and is fixed below vernier scale. The vernier scale is capable to measure the position of Pitot tube in transparent section. The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

EXPERIMENTATION:

To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube.

To plot velocity profile across the cross section of pipe.

UTILITIES REQUIRED:

Electricity Supply: Single Phase, 220V AC, 50Hz, 5-15 amp combined socket with earth connection.

Water Supply (Initial Fill).

Floor Drain required.

Floor Area Required: 1.5 x 0.75 m.

Chemical Required: CCl4 - 50 ml and Iodine pallets for CCl4.

TECHNICAL DETAILS:

Pitot tube Material Copper/SS of compatible size fitted with vernies scale.

Test Section Material Clear Acrylic, compatible to 1” Dia. Pipe.

Water Circulation FHP Pump, Crompton make.

Flow Measurement Using Measuring Tank with Piezometer (Capacity 25 Ltrs.)

Electronic Stop Watch

Sump Tank Capacity 50 Ltrs.

Control Panel Comprises of :

Standard make On/Off Switch, Mains Indicator, etc.

Instruction Manual An ENGLISH instruction manual will be provided along With the Apparatus Tanks will be made of Stainless Steel.

CAVITATION APPARATUS MAKE : CREATIVE LAB MODEL NO: CLFM-15

DESCRIPTION :

The apparatus has been designed to demonstrate the phenomena of Cavitation. The present set-up consists of a test section made of Acrylic having conversion and diversion section. Pressure tapings at appropriate position are provided. This test section is having one control valve at upstream side to regulate the water flow rate. Two pressure gauges are connected to these taping which give the pressure readout at the time of flow passing through this test section. The unit is self-contained close circuit type with sump tank, measuring tank and centrifugal pump. Flow through test section can be regulated with the help provided by-pass and control valve.

EXPERIMENTATION:

To observe the phenomena of cavitation.

To compare the theoretical and actual pressures at cavitation condition.

UTILITIES REQUIRED :

Water Supply : Initial Fill.

Floor Drain Required.

Floor Area Required : 1.5 m x 1 m.

TECHNICAL DETAILS :

Test Section : Material Acrylic

Pressure Gauge : 0-4 kg/cm2

Vacuum Gauge : 0-760 mmHg

Water Circulation : By Pump Crompton make.

Flow Measurement : Measuring Tank (Capacity : 40 liters) & Electronic Stop Watch

Sump Tank : Capacity : 60 liters

Control Panel Comprises of :

Standard make On/Off Switch, Mains Indicator, etc.

Instruction Manual : An ENGLISH instruction manual will be provided along

with the Apparatus Tanks will be made of Stainless Steel.

The whole set-up is well designed and arranged in a good quality painted structure

LAMINAR FLOW TABLE MAKE :CREATIVE LAB MODEL NO:-CLFM-16

DESCRIPTION :

The present set-up is designed to visualize the ideal flow around immersed body. It consists of a flow table in which flow of water is circulated in between two transparent sheets with a small gap between them. Water is supplied to the table and a coloured dye is injected in the inlet of flow at different location. Water from the sump tank is pumped by a centrifugal pump to a calming section for table and after passing through transparent sheet it goes to sump tank. By-pass and flow control valves are provided to regulate the flow.Flow is made laminar by operating inlet control valve for water and it is visualized due to transparent sheet and colour. A small capacity dye tank will be provided for the flow of dye in fluid inlet stream. Any obstacle can be placed between the sheets and change in flow pattern can be visualized. Obstacles of different types will be supplied with the apparatus.

EXPERIMENTATION:

To visualize the ideal flow around the immersed bodies of different types.

UTILITIES REQUIRED:

Electricity Supply: single phase, 220 V AC, 50 Hz, 5-15 amp combined socket with earth connection.

Water Supply (Initial fill).

Floor Drain required.

Floor Area Required: 1 m x 0.5 m.

Chemical Required: Dye (KMnO4) – 10 gm

TECHNICAL DETAILS :

Flow Table

Length : 750 mm (approx.)

Width : 500 mm (approx.)

Material : Stainless Steel

Transparent Sheets : Material Glass/Acrylic (Qty: 2 Nos.)

Water Circulation : FHP Pump Champion/ godrej make.Sump Tank

Capacity : 40-50 Ltrs

Material : Stainless Steel

Dye Vessel

Capacity : 1 Ltrs

Material : Stainless Steel

Instruction Manual : An ENGLISH instruction manual will be provided along

with the Apparatus

Whole set-up is in well designed and arranged in a good quality painted structure.

METACENTRIC HEIGHT APPARATUS MAKE : CREATIVE LAB MODEL NO:-CLFM-17

DESCRIPTION:

A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc.For tilting the ship model, a cross bar with movable hanger is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.

EXPERIMENTATION:

Determination of the metacentric height and position of the metacentric height with angle of heel of ship model.

UTILITIES REQUIRED :

Water Supply : Initial Fill

Floor Area 1 m x 0.6 m.

Drain required.

TECHNICAL DETAILS:

Pontoon: Size 300 x 300 mm (approx.) with a Horizontal Guide Bar for aliding weight and Removable Strips, Graduated Arc with Pointer with moveable hanger and set of weights.

Water Tank : Size 550 x 500x 400 mm (approx.)

Front Window of Tank: Made of Glass/Perspex.A set of weights is supplied with the apparatus.

Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus Tanks will be made of Stainless Steel.

Pendulum and graduated are for accurate measurement of Tilt angle.

Prev 1 2 3 4 5 6 Next

METACENTRIC HEIGHT APPARATUS MAKE : CREATIVE LAB MODEL NO:-CLFM-17 LAMINAR FLOW TABLE MAKE :CREATIVE LAB MODEL NO:-CLFM-16 CAVITATION APPARATUS MAKE : CREATIVE LAB MODEL NO: CLFM-15 PITOT TUBE SETUP MAKE : CREATIVE LAB MODEL NO:-CLFM-14 NOZZLE METER TEST RIG MAKE : CREATIVE LAB MODEL NO:-CLFM-12